Chatt-State CDL Class A Pre-Trip Inspection Practice Exam

These questions are part of the practice quiz. Start practicing

• What does PMS stand for in a CDL context?
• Why is it important to inspect the mirrors?
• What is the minimum requirement for DOT tape on lights and reflectors on the side of the trailer?
• In a pre-trip inspection, what indicates the exhaust system is in a good condition?
• What should you check first under the hood during a pre-trip inspection?
• How can you confirm that the suspension is not damaged during inspection?
• What is an indicator of properly functioning windshield wipers during a pre-trip inspection?
• What should the condition of the rim be during a pre-trip inspection?
• What is required when checking the tires during a pre-trip inspection?
• During a service brake test, at what speed should you roll forward?
• What should be verified for the windshield wipers during a pre-trip inspection?
• What is the requirement for lights and reflectors on the side of the trailer?
• What should be checked regarding the air compressor during a pre-trip inspection?
• Which item is necessary for proper visibility during adverse weather conditions?
• What should you do when asked to perform the air brake test by the examiner?
• What condition should the alternator belt be in during a pre-trip inspection?
• During a tire inspection, how can one check for belt separation?
• What should you confirm about the turn signals during the light check?
• How should the fifth wheel be inspected?
• What is NOT a step in inspecting the fuel tank during a pre-trip check?
• When inspecting the fuel tank, what is essential for its securement?
• How can you identify a defective tire?
• Which of the following is NOT a requirement for electrical wires during inspection?
• What condition should the door hinges of the trailer be in during a pre-trip inspection?
• What condition should the frame of the trailer be in for a proper inspection?
• How should the windshield condition be during a pre-trip inspection?
• What condition should the brake chamber and clamp be in?
• During a pre-trip inspection, how should the air bag be positioned?
• Which component must be free from illegal drills or welds according to inspection standards?
• Which part should NOT be missing hardware during inspection?
• How far from your vehicle should you place a safety triangle when near a hill or curve?
• What requirements do lights and reflectors at the rear of the trailer need to meet?
• What should you check on the vehicle's windshield?
• What is a key indication of the condition of the alternator wires during inspection?
• During a pre-trip inspection, the door must meet which criteria?
• How do you check for air leaks in the air lines?
• What is the correct procedure for checking the oil dipstick according to pre-trip inspection guidelines?
• What is one aspect to verify with the pitman arm and drag link during inspection?
• On a one-way highway, where should safety triangles be set?
• Which component is crucial for the proper function of the air brake system?
• What is critical to check about the steering arm during a pre-trip inspection?
• What should you look for on the tires during the inspection?
• What is the proper way to assess the condition of the exhaust system?
• When checking the trailer's brakes, what should be avoided?
• Where is the engine oil dipstick usually located?
• Why is it important to check the emergency equipment on the truck?
• How do you assess the condition of the springs?
• What are the signs of a leaking air brake system?
• During an inspection, what signifies that there might be a leak in the exhaust system?
• What does ABC signify in the context of brake hose inspections?
• What should you be cautious of when placing safety triangles?
• What is required for landing gear, pads, and handles during inspection?
• What should you check about the seatbelt during a pre-trip inspection?
• How should the air pressure be checked in the brake system?
• How do you inspect the lights on the vehicle?
• What should you tell the examiner after performing the brake tests?
• While inspecting the steering gear box, what must be checked?
• When performing a trailer brake test, what should be engaged?
• What action is required for the pigtail during inspection?
• What is the importance of checking the air cleaner during a pre-trip inspection?
• What should be checked regarding the brake system during the pre-trip inspection?
• How much pull should there be when brakes are released according to inspection standards?
• Which items are typically included in the emergency equipment checklist?
• How should the pre-trip inspection be documented?
• What is one way to ensure safety when inspecting trailer connections?
• How should you check if all emergency lights are functioning?
• In checking the marker light by the driver door, what must be ensured?
• What indicates that lug nuts may be loose during an inspection?
• When inspecting shocks, what condition should be noted?
• What is a crucial aspect of inspecting the truck's lighting system?
• During a pre-trip inspection, what should be visually checked on metallic parts?
• What does PMS stand for in the pre-trip inspection context?
• Which of the following is acceptable condition for hardware during a pre-trip inspection?
• Which tool is commonly used to measure tire tread depth?
• What is indicated by the acronym ABC during a vehicle inspection?
• Which components should be connected by castle nuts and cotter pins?
• Why is the frame of the truck important to inspect?
• What condition should the power steering pump be in during inspection?
• If the brakes are continuously pumped, what should occur?
• How can rust on the vehicle be inspected during the pre-trip inspection?
• What is a critical aspect of checking the air pressure in tires?
• What components are checked in the steering system?
• How often should the exhaust system be checked during a pre-trip inspection?
• What does "PMS" typically refer to in the context of vehicle inspection?
• What is a normal finding on the truck's frame during an inspection?
• What is the acceptable condition for the front of the trailer and bulkhead?
• What should be done if a mechanical issue is found during a pre-trip inspection?
• What type of horn must be checked during a pre-trip inspection?
• What specifications should the fire extinguisher meet during inspection?
• What should the sliding 5th wheel position ensure?
• What condition should the floor of the trailer be in during a pre-trip inspection?
• What is the most important aspect of checking the wiper fluid reservoir?
• Which of the following is NOT one of the five required safety items in a truck?
• What do you need to check for when inspecting the trailer's brakes?
• What is the minimum tire pressure reading during an inspection?
• What should be done regarding the water pump belt during inspection?
• What should be assessed regarding the catwalk during the inspection?
• What condition should the drive shaft and U-joints be in during inspection?
• What is an acceptable condition for the air lines?
• What should be noted about the condition of the catwalk and catwalk steps?
• What should the coolant reservoir be checked for during a pre-trip inspection?
• What is the purpose of the rubber straps under the metal straps on the fuel tank?
• What should be checked in the brake system during pre-trip inspections?
• How should the governor cut-out pressure be checked?
• What is the acceptable amount of play in the steering arm during a pre-trip inspection?
• What aspect of the mirrors should be checked during a pre-trip inspection?
• Why is it important to check the coolant level in the radiator?
• What should you inspect on a truck's frame during a pre-trip inspection?
• What should you inspect on the battery during the pre-trip inspection?
• What is the purpose of the pre-trip inspection in a CDL Class A vehicle?
• What condition should the brake drum be in during a pre-trip inspection?
• What is a critical factor regarding the steering column during the pre-trip inspection?
• How do you inspect the brake pads and linings?
• What is checked on the frame of the tractor during a pre-trip inspection?
• How is a tractor brake test performed?
• How many safety triangles are required in a truck?
• What condition should the universal joint (U-joint) be in according to inspection requirements?
• When inspecting the power steering reservoir, which aspect must be verified?
• What is the proper way to check the coupling devices on a tractor-trailer?
• What is the primary purpose of confirming load weight before a trip?
• What is important when checking the brake hose?
• What is the purpose of checking the suspension system?
• What is the minimum thickness for brake pads during a pre-trip inspection?
• In what condition should the hub axle oil be during inspection?
• What should the hub axle assembly be checked for during a pre-trip inspection?
• What is the critical aspect of the tractor frame during inspection?
• How deep should the tire tread be at a minimum during the inspection?
• What could be a consequence of failing to perform a thorough pre-trip inspection?
• What is a requirement for mud flaps during a pre-trip inspection?
• During inspection, where must the landing gear pads be located?
• What should be verified about the 5th wheel skid plate and release arm?
• Why is fluid level inspection important?
• What should the inspection include regarding the lights on the vehicle?
• What should be checked regarding the load securing methods?
• What is the importance of the platform's condition during inspection?
• What should the tandem release and locking pins be like during inspection?
• Where is the pigtail receptacle located?
• What does a successful brake test indicate regarding vehicle safety?
• Where should the spare fuses be located in a truck?
• Why should you inspect the air pressure in the auxiliary tanks?
• How far should the second safety triangle be placed behind a vehicle on a two-lane roadway?
• During an inspection, what angle should the slack adjuster and push rod form when the brakes are applied?
• What is a critical requirement for the release arm of the 5th wheel?
• What is the primary purpose of the tire inspection during pre-trip?
• What should be checked regarding the glad hands and connectors?
• How should the back of the tractor be inspected in terms of hardware?
• What is the maximum allowable air pressure loss in the applied leak down test?
• What condition should the taillights of a tractor be in according to the pre-trip inspection standards?
• Where should the first safety triangle be placed on a two-lane roadway?
• Why is it necessary to verify the load weight during a pre-trip inspection?
• What does PMS stand for in the context of vehicle inspections?
• What is the normal primary and secondary air gauge reading for a vehicle?
• What should you verify regarding the spring hangers?
• In pre-trip inspections, what does CDL stand for?
• How often should a driver conduct a pre-trip inspection?
• What does a vehicle's locking jaws need to pass inspection?
• When should the lights and buzzers activate in the air brake check?
• Which of the following is NOT part of the BBC acronym?
• What should the condition of the taillights and brake lights be, according to inspection standards?
• What condition applies to the glad hands gasket during inspection?
• What is the minimum tread depth required for commercial truck tires?
• Why is it critical to verify no illegal welds on the king pin apron?
• What condition should the valve stem and cap be in during a pre-trip inspection?
• What is not a sign of brake lining failure during inspection?
• What condition must be checked regarding the air lines of the air compressor?
• Why is it important to check the dash warning lights during a pre-trip inspection?
• How should the water pump be assessed during the inspection?
• What is an appropriate measure of suspension condition?
• What is the ideal condition for tire tread across the top during inspection?
• What should you check for in the tire sidewall during an inspection?
• What is the minimum height requirement for the brake hoses on the side of the trailer?
• What does the pre-trip inspection help drivers comply with?
• What should be ensured about the DEF tank and cap during a pre-trip inspection?
• What should the condition of the mirror be during inspection?
• Which of the following is NOT included in the list of truck items to check?
• What needs to be checked for universal bolts (U-Bolts)?
• When inspecting the king pin apron and king pin, what must be ensured?
• How do you check the function of the wiper blades?
• In terms of shocks, what could indicate a potential problem?
• Why must you check the coupling height on a tractor-trailer?
• How do you check the fuel system for leaks?
• What is an acceptable condition for the air bag in relation to shocks?
• What should be checked regarding the ICC bumper?
• What should you look for when inspecting the fuel tank?